Just How to Set up a Tub
Just How to Set up a Tub
Blog Article
Just how do you really feel on the subject of Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't exactly rocket science, but it does need solid plumbing, woodworking, as well as often, tiling abilities. Replacing an old bathtub with a brand-new one is also a moderately tough task. If the old bathtub is readily available, the project can move rapidly; if you need to open up a wall surface to remove the old tub and position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will need a helper to leave the old bathtub as well as set in the new one. Ensure you have qualified on your own for the task as well as fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is better to consider employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your shower room if you have actually currently purchased a new tub and don't need to transform the setup of your previous water pipelines.
Your tools and material checklist ought to make up the following:
Preparing for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to stop stress on the tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water system. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome because of the limited access that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric ready for the remaining water that will certainly originate from the pipelines. Once the supply pipes have been gotten rid of, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing substance.
Prior to going on to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, position the bath tub in the required placement. The wood boards are handy in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub till the spirit level checks out level.
To set up taps, fit all-time low of the outermost versatile faucet adapter to the proper supply pipe by making a compression sign up with; after that do the same for the other tap.
Turn on the water and also examine all joints and also brand-new pipework for leakages and tighten them if necessary. Load the bathtub and also check the overflow outlet and the normal electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the tub ought to wait until the bathtub has been made use of at the very least when as this will certainly resolve it into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Protect the tap in place with the supplier supplied backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The previous kind ought to be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, triggering the water to permeate the wall in between the bathroom and the tiling, bring about issues with dampness as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your fixtures and installations. They are sold in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to allow for the motion experienced when the tub remains in use. The sealer can crack relatively early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader about How to Install a Bathtub Yourself, I was thinking sharing that section was essential. You should take a moment to promote this blog post if you appreciated it. I appreciate reading our article about Tools You Need to Install a New Bathtub .
Get Quote
Report this page